<rp id="srq49"></rp>

    1. <li id="srq49"><tr id="srq49"></tr></li>

    2. BEIJING ANSHUNTAI CONSTRUCTION TECHNOLOGY CO.,LTD.
      — 產品展示 —

      安順泰墻坭高強粉刷石膏

      安順泰墻坭高強粉刷石膏
      【產品簡介】
      安順泰墻坭高強粉刷石膏采用進口添加劑,配以國內優質填料生產制作而成, 是一種性能優良的建筑內墻及頂板抹灰新型材料,產品分底層、面層兩部分,粉狀,加水攪拌均勻后即可使用,是傳統抹灰材料(混合灰和白水泥)的換代產品。本品無毒、無味且具有調節空氣濕度、殺菌等作用,是綠色環保的健康產品。
      【用 途】
      本品適用于磚墻、現澆混凝土墻、加氣混凝塊墻、石膏砌塊墻、頂棚、特別適用于砼頂板、加氣砼墻面及各種保溫材料的表面抹灰。
      【主要成份】
      半水石膏、碳酸鈣、沙(底層)、緩凝劑、有機膠粉、有機纖維、添加劑等
      【產品性能指標】
      1.凝結時間:
      初凝時間≥1小時  終凝時間≤ 8小時
      2. 可操作時間:大于60分鐘。
      3.保水性:
      面層安順泰墻坭高強粉刷石膏≥90%,底層安順泰墻坭高強粉刷石膏≥75%
      4.強度:
      抗折強度面層≥3.0Mpa,底層≥2.0Mpa ,抗壓強度面層≥6.0Mpa,底層≥4.0Mpa
      【產品優點】
      安順泰墻坭高強粉刷石膏是一種新型墻體抹灰材料,具有傳統混合灰所無法比擬的優點和特性。隔音性能:安順泰墻坭高強粉刷石膏在凝結過程中,內部產生微小的孔隙,因此能衰減聲壓,又可防止聲能透射,故具有良好的隔音性能。
      呼吸功能:安順泰墻坭高強粉刷石膏硬化過程中,形成無數個微小的蜂窩狀呼吸孔,當室內環境濕度較大時,呼吸孔自動吸濕;在相反條件下,能自動釋放儲備水分,這樣反復循環,巧妙地將室內濕度控制在適宜范圍之內,為居住者創造了良好舒適的生活環境。衛生保健性:石膏不但是一種綠色建材,本身也是一種藥材,有消毒殺菌的作用,在石膏材料裝修的房間里,細菌難以生存和傳播。因此,用石膏制品取代有氣味、不透氣的裝潢材料,對人體健康有益。用石膏粉刷的房間尤其適用于嬰幼兒和老年人居住。
      【基層處理及操作工藝】
      1.安順泰墻坭高強粉刷石膏前將基體表面灰塵、雜物、隔離劑等處理干凈,做到平整干凈,無灰塵,無油污。請根據不同基層材料適當充分噴水潤濕,但不能在基體表面有水的情況下作業。
      2.抹灰前對較干燥的墻面適量噴水濕潤,但有明顯潮濕和水珠的墻面應暫緩施工。
      3.料漿配制:一次投料量應是在可使用時間內用完的料漿使用量,初凝后的料漿不得再加水攪拌使用;料漿配制必須攪拌均勻才可使用,稠度要比水泥砂漿稍??;在氣溫超過℃30℃或風力在四級以上時,料漿的配制要比平常再稀一點,以保證抹灰層質量;料漿攪拌用水應是清潔無雜質的。
      4.手工抹灰:根據施工情況先沖筋。沖筋的間距根據房間的高度決定,一般在墻面的底、上部沖筋兩道即可。沖筋完畢后即可進行抹灰操作。
      5.抹灰厚度≤2mm時,可直接使用面層型安順泰墻坭高強粉刷石膏;抹灰厚度>3mm時,先用底層型安順泰墻坭高強粉刷石膏打底、抹平,再用面層型安順泰墻坭高強粉刷石膏罩面。
      6.當抹灰厚度超過時,應該分層施工,每層厚度在以內,待上一層料漿終凝后再抹一下層。
      7.壓光應在終凝前進行,一般在抹灰后30分鐘左右,用指按壓表面不出現明顯壓痕為宜。
      8.刮涂率距刮涂厚度有所不同。
      【注意事項】
      1.加水的石膏應在初凝前用完,初凝后的料漿不得加水使用。
      2.施工完畢的墻面應避免磕碰及水沖浸泡,并要保證室內通風良好。
      3.現場施工溫度應超過零下5℃。
      【貯存、運輸和包裝】
      1.本品應貯存在干燥處,嚴禁受潮。
      2.標準儲存狀態下儲存期為12個月。
      3.本品運輸按《非危險品運輸規則》處理。
      4.儲運要防潮防雨。
      5.包裝:20㎏/袋、
       

      【產品簡介】Product Profile
      Anshuntai High-strength Plastering Gypsum is made of high-quality fillers and imported additives. It is a new type
      of well-performing plastering material for interior walls and ceilings. The product include two versions: one for the
      foundation coating and the other for the top coating. The powder-formed product can be used after well mixed
      with clean water. It is a modern day alternative solution to traditional platering material (Sand Cement Plaster).
      This product is not only non-toxic and odorless, but also able to regulate air humidity and disinfect the
      envinroment. It is a green and safe product.
      【用 途】Scope of Application
      This product is suitable for surface plastering of brick wall, cast-in-place concrete wall, aerated concrete block
      wall, gypsum block wall, ceiling, especially for concrete plate, aerated concrete wall, besides various insulation
      materials.
      【主要成份】Ingredients
      Semi-hydrated gypsum, calcium carbonate, sand (the foundation version), retarder, organic rubber powder,
      organic fiber, additives, etc.
      【產品性能指標】Technical Parameters
      1. Setting Time
      Initial Setting Time ≥ 1 hour
      Final Setting Time ≤ 8 hours
      2. Pot Life: No shorter than 60 minutes
      3. Water Retension
      Top Coating Version ≥ 90%
      Foundation Coating Version ≥ 75%
      4. Strength
      - Fracture Strength: Top Coating Version ≥ 3.0Mpa, Foundation Coating Version ≥ 2.0Mpa
      - Compression Strength: Top Coating Version ≥ 6.0Mpa, Foundation Coating Version ≥ 4.0Mpa
      【產品優點】Product Features
      Anshuntai High-strength Plastering Gymsum is an alternative solution to the traditional wall plastering material,
      Sand Cement Plaster. Comparing to the traditional material, the product has the following strengths:
      - Sound Insulation: In the process of condensation, tiny pores are formed inside the product. These pores can
      attenuate the sound pressure and weaken the transmission of sound energy.
      - Humidity Regulation: In the process of hardening, numerous tiny honeycomb-shaped breathing holes are
      formed in the product. When the indoor environment is in high humidity, the breathing holes can automatically
      absorb the moisture; in the opposite situations, the reserved moisture in those holes can be automatically
      released. In this way, the indoor humidity is maintained within a suitable range, creating a comfortable living
      environment.
      - Disinfection: Gypsum is not only a kind of green building material, but also a kind of Chinese medicine. It is said
      to be able to disinfect and sterilize the environment. In the room where the gypsum material is used, bacteria are
      difficult to survive. Therefore, replacing odorous and airtight finishing materials with gypsum products is a good
      way to ensure health. Rooms finished by Gypsum materials are especially good for infants and the elderly.
      【基層處理及操作工藝】Surface Preparation and Application
      1. Before application, make sure the surface is clean and free from dust, grease or separant. Please pre-wet the
      surface by spraying a proper amount (depending on the substrate materials) of water, but do not start the next
      step when there is water hanging on the surface of the substrate.
      2. Before the plastering, apply a proper amount of water to the wall if it is rather dry, but the next step should be
      held if the wall is seen with water hanging on the surface.
      3. Mixing and Blending: The dosage of product each time should not exceed the amount that may exhaust the pot
      life. After the end of initial setting time, no more water should be blended into the paste for further use. Please
      make sure the paste should be uniform and lump-free, and it should be a bit less thick than cement mortar. When
      the temperature is higher than 30 °C or the wind is stronger than the fourth grade, the paste should be thinner
      than usual to ensure the quality of the plastering. Only clean water should be used.
      4. Reference Marks Placement. Place aluminum box plate on bull marks. The space between two marks depends
      on the height of the wall.
      5. Manual Plastering:If you wish the coating thickness to be ≤2mm, you may use the product (Top Coating
      Version); if >3mm, use the product (Foundation Coating Version) as a base and levelling, and apply a second
      coating upon that using the product (Top Coating Version).
      6. If you wish the coating to be >3mm, multiple coatings should be applied, and each coating thickness should
      not exceed the limit. On after the fianl setting time past for the first coating, a second coating can be applied.
      7. Press polishing should be done before the end of final setting time, which is approximately 30 minutes after
      plastering. Use your finger to press on the surface to check if it is done (if leaving no obvious print, it is done.)
      8. The coating thickness can vary.
      【注意事項】Precautions
      1. The paste should be used up before the end of inistial setting time. After the end of initial setting time, no more
      water should be blended into the paste for further use.
      2. The finished wall should be kept from being bumped or contact with water, and make sure the indoor ventilation
      is functioning well.
      3. The temperature at the time of application should not be lower than - 5°C.
      【貯存、運輸和包裝】Storage, Transportation and Pakage
      1. This product should be stored in a dry place, and carefully kept from exposure to moisture.
      2. If stored properly the product life is 12 months
      3. Transportation should be arranged in accordance with Non-Dangerous Goods Transportation Regulations.
      4. To keep the products from exposure to moisture and rain is the key in storage and transportation.
      5. Package: 20 KG / Pack
      電話
      郵箱
      地圖
      分享
      聯系
      亚洲Av图片日韩
      <rp id="srq49"></rp>

      1. <li id="srq49"><tr id="srq49"></tr></li>