<rp id="srq49"></rp>

    1. <li id="srq49"><tr id="srq49"></tr></li>

    2. BEIJING ANSHUNTAI CONSTRUCTION TECHNOLOGY CO.,LTD.
      — 產品展示 —

      美佳襯6A耐水膩子粉

      美佳襯耐水膩子粉(AST6A)
      【產品簡介】
      本品采用德國8A集團進口材料及生物凈化技術研制的粉狀耐水墻面找平材料。采用德國8A技術配方及材料,白度高、細度好、施工簡便,產品固化后具有優良的耐水性和粘結強度。適用于室內混凝土、砂漿和石膏墻面基層批刮找平。本品符合中國國家環保標準并獲得德國8A集團授權使用標志認證產品。
      【產品特性】
      1、施工性好:本品具有很好的施工性和打磨性。
      2、一次裝修長期受益避免傳統膩子3-5年后出現粉化、起皮、脫落現象而不得不進行二次裝修。
      3、二次裝修無需鏟除,有效避免建筑垃圾的產生,屬綠色節能環保產品。
      【消耗量】
      理論上,1公斤“美佳襯AST 6A”可以批刮1平方(兩遍)。實際用量因施工方法、基層平整度的不同而不同。
      【攪  拌】
      水的加入量以施工稠度為準,攪拌均勻后,放置15分鐘(冬季30分鐘)。再進行攪拌即可使用。不可以加入其他材料混合使用,加水攪拌后在桶中的存放時間約為20小時(25±2℃),在桶中存放時,表面應覆蓋,避免失水干燥。
      【基層處理】
      基層應干燥、堅實,不能有浮灰、油漬、污物及可溶于水的膩子,基層含水率應低于5%。如果基層平滑或疏松,需用“璧寶AST-6A”進行界面處理,待干透后方可批刮“美佳襯AST 6A”。
      【批刮找平】
      可以用抹子和刮板批刮找平。膩子找平應在半干狀態下(用手輕壓不變形)完成,固化后可用360目細砂紙打磨找平。膩子批刮厚度超過3㎜,應分次批刮,每次批刮厚度不大于2㎜。一次批刮過厚易出現干縮開裂。
      【注意事項】
      1、施工環境溫度和固化過程溫度應在8℃以上。
      2、本品嚴禁摻加其他助劑、膠類混合使用。
      【貯存、運輸和包裝】
      1、本品應儲存在陰涼通風處,嚴禁曝曬和受潮。
      2、貯存環境溫度應控制在5~35℃。
      3、在標準狀態下儲存期為18個月。
      4運輸按《非危險品運輸規則》辦理。
      【執行標準】JG/T298-2010(N);環保標準:GB18582-2001.

      Meijiachen Waterproof Putty Powder
      【產品簡介】Product Profile
      This product is a powdered waterproof leveling material for wall, developed with materials and biological
      purification technology imported via 8A Group (a Germany-based company). The product has the advantages of
      high whiteness, good fineness and ease of application. Cured surface provides excellent hydrophobicity and
      shows remarkably distinct anti-efflorescence effect in comparison to traditional powder putties. It is suitable for
      interior leveling of concrete, mortar or gypsum substrate. This product complies with China's national
      environmental protection standards and is certified by 8A Group.
      【產品特性】Product Features
      1. Good Applicability: This product shows good applicability and sanding property.
      2. Anti-efflorescence Effect: Cured surface after using this product shows remarkable anti-efflorescence effect in
      comparison to traditional putty powder resulting efflorescence within only three to five years. Thus this product
      provides extended life of top coatings.
      3. Environmentally-friendliness: No need for removal at re-application, which reduces construction waste and
      validates our commitment in striving towards a greener future.
      【消耗量】Coverage
      Theoretically, the product “Meijiachen AST 6A” can cover 1 m 2 /KG for two coats. The actual coverage may vary
      depending on the efficacy of the applicator and the quality of the substrate.
      【攪 拌】Mixing and Blending
      Mix the product with an appropriate amount of clean water and start blending until it becomes a uniform,
      lump-free paste. Leave the paste for 15 min (30 min in winter), and then blend again. Do not add any other
      materials. The paste could be kept in a tank with a cover (to slow down the drying process) for no longer than 20
      hours (25±2℃).
      【基層處理】Surface Preparation
      The substrate should be dry, hard and free from dust, grease or hydro-soluble putty. The water content of
      substrate should be lower than 5%. If the substrate is loose or lumpy, it is advisable to use our product “Bibao
      AST-6A” and wait until it is dried, before applying “Meijiachen AST 6A”.
      【批刮找平】Application
      A trowel or a putty blade may be used. The putty should be applied when it is semi-dry (i.e. when slight pressure
      doesn’t cause deformation), and it can be sanded and leveled with sandpaper P360 when the putty is dried. Each
      coating should not be thicker than 2mm. If you wish it to be as thick as 3mm or beyond, you need to do a second
      coating. Exceeding the limit of thickness of each coating could lead to shrinkage cracks.
      【注意事項】Precautions
      1. The temperature at the time of application and drying should not be lower than 8°C.
      2. Do NOT mix this product with other aids or adhesive products。
      【貯存、運輸和包裝】Storage, Transportation and Package
      1. This product should be stored in a cool and ventilated place, and it is strictly prohibited to expose to the sun and
      moisture.
      2. The temperature of storage should be between 5 and 35 °C.
      3. If the product is stored properly, the product life is 18 months.
      4. Transportation should be arranged in accordance with Non-Dangerous Goods Transportation Regulations.
      【執行標準】Execution Standard: JG/T298-2010(N)
      【環保標準】Environmental Protection Standard: GB18582-2001

      電話
      郵箱
      地圖
      分享
      聯系
      亚洲Av图片日韩
      <rp id="srq49"></rp>

      1. <li id="srq49"><tr id="srq49"></tr></li>